DLA MS27424 REINST NOTICE 2-2006 駕駛員座艙效用燈夾集合

MS27424, dated 6 December 1965, is hereby reinstated as inactive for new design and may be used for acquisition.

CLIP ASSEMBLY, COCKPIT UTILITY LIGHT

DLA A-A-51140 B VALID NOTICE 1-2006 鍵類型連接的三爪鉆夾頭

A-A-51140B, dated 25 September 2000, has been reviewed and determined to be valid for use in acquisition.

CHUCKS, DRILL, KEY TYPE, THREE-JAW, GEARED

ARMY A-A-52529 VALID NOTICE 1-2004 公制消聲器和尾管排氣管吊架

A-A-52529, dated 13 October 1995, has been reviewed and determined to be valid for use in acquisition

HANGER, EXHAUST, MUFFLER AND TAILPIPE (METRIC)

ARMY A-A-52528 VALID NOTICE 1-2004 公制消聲器和尾管排氣管托架

A-A-52528, dated 13 October 1995, has been reviewed and determined to be valid for use in acquisition

BRACKET, EXHAUST, MUFFLER AND TAILPIPE (METRIC)

DLA MS39046 REV A VALID NOTICE 2-2003 (電桿上線路)捆綁的電夾

MS39046A remains inactive for new design, however, the document is valid for use

CLAMP, ELECTRICAL, LASHING (POLE LINE)

DLA A-A-52127 VALID NOTICE 1-2001 ( 5英寸)洗衣網兜夾

A-A-52127, dated 15 June 1993, has been reviewed and determined to be valid for use in acquistion.

PIN, NET, LAUNDRY, (5-INCH)

DLA A-A-51140 B-2000 鍵類型連接的三爪鉆夾頭

This commercial item description (CID) establishes the government acquisition requirements for geared three-jaw drill chucks capable of being adjusted to hold any size straight shank tool within the capacity of the chuck. The jaws of the chuck shall be opened and closed by means of a pinion- type key.

CHUCKS, DRILL, KEY TYPE, THREE-JAW, GEARED

AECMA PREN 3078-1998 航空航天系列帶橡膠墊的P、Q和鞍形夾持器　技術規范

This "Aerospace Series'' Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries.

Aerospace Series P, Q and Saddle Clamps with Rubber Cushion Technical Specification Edition P 1

QJ 794.1A-1997 機床夾具零件及部件 單柄螺母 螺母

Machine Tool Fixture Parts and Components Single Shank Nuts Nuts

DLA MS27405 REV A NOTICE 2-1997 電子管夾

This notice should be filed in front of MS27405A dated 23 DECEMBER 1971.

CLAMP - TUBE

DLA MIL-C-496 D NOTICE 1-1997 帶尾夾

MIL-C-496D is inactive for new design and is no longer used except for replacement purposes.

CLIPS, END, STRAP

DLA MIL-C-8603 B NOTICE 1-1997 環形帶支撐夾子

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

CLAMPS, LOOP TYPE, AND STRAPS, SUPPORT

QJ 806A-1997 機床夾具零件及部件 帶軸向緊固螺桿齒條式定位器

Machine tool fixture parts and components with axial fastening screw rack type positioner

QJ 94.1A-1997 機床夾具零件及部件 Ⅴ型定位器 Ⅰ型定位器

Machine Tool Fixture Parts and Components Type V Locator Type I Locator

QJ 74.2A-1997 機床夾具零件及部件 車床花盤保險裝置 內六角螺釘

Machine Tool Fixture Parts and Components Lathe Faceplate Safety Device Hexagon Screws

QJ 806.1A-1997 機床夾具零件及部件 帶軸向緊固螺桿齒條式定位器 定位銷

Machine tool fixture parts and components with axial fastening screw rack type locator positioning pin

QJ 806.2A-1997 機床夾具零件及部件 帶軸向緊固螺桿齒條式定位器 襯套

Machine tool fixture parts and components with axial fastening screw rack type positioner bushing

QJ 806.3A-1997 機床夾具零件及部件 帶軸向緊固螺桿齒條式定位器 齒套

Machine tool fixture parts and components with axial fastening screw rack type locator tooth sleeve

DLA A-A-55099 A-1997 蚊帳的棒和夾子

This commercial item description covers a rod and clamp assembly used in supporting insect bars over certain types of military beds and cots.

ROD AND CLAMP, INSECT BAR

QJ 98A-1997 機床夾具零件及部件 支座

Machine tool fixture parts and component supports